Athena IMP Instruction Manual

HOT RUNNER CONTROLLERSSERIES IMP IMP/P SAMInstructionManual

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual7Standby Heat (SAM module only)Standby heat is a low heat level used to keep heaters and as

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual8switched to manual mode. The output power will be a function of the manual control knob se

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual9User’s Selected Jumper Option1. For degree Celsius operation, install jumper on PCboard ma

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual10SafeChange. SafeChange should be enabled on the controller before installing it in the ma

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual11If you don’t see JP6, thecontroller in hand may pre-date the SafeChange feature. In addit

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual12InstallationNever insert or remove the module from a mainframe withthe AC power on. Alway

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual13Standby TemperatureAC Input RequirementsAlarm LimitsAlarm Output (Audible)Alarm Output (V

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual14SAM MODULEQUICK REFERENCE GUIDESPEAKERFAST, HIGH TONE = OVER TEMPERATURE 30°F (17°C)OR MO

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual151. Select Normal or Standby Mode.2. Select Low Temperature Alarm Mode.a. Low Temperature

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual16the over temperature LED will flash, and relay closure will occur.b. Under Temp. : Occurs

Athena Controls, Inc.5145 Campus Drive Plymouth Meeting, PA 19462Phone: 610-828-2490Fax: 610-828-7084www.athenacontrols.comYou can reach our technical

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual175. Remote Standby Option: It is possible to wire the mainframefor remote standby operatio

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual18NOTES

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual19MOLDv(FEMALE)CABLE ENDCKPTF1CABLEMPT/C10 (10 FOOT)MPT/C20 (20 FOOT)(MALE)vCABLE ENDCKPTM1

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual20IMP/P 10BPOWER CORD IN,5 PIN OUTAC INPUTOUTPUTSERIES IMP/P WIRING & CONNECTION DIAGRA

For technical assistance, call toll free 1-800-782-6776 (in the U.S.) or 610-828-2490(from anywhere in the world), or e-mail techsupport@athenacontrol

Section 11.11.21.3Section 22.12.22.32.4IMP I IMP/P I SAM Hot Runner Controllers Instruction ManualTable of ContentsIMP I IMP/P SeriesGeneral Descripti

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual1IMP SERIESOPERATING INSTRUCTIONSALARM/MODE DISPLAYDISPLAY ALARM SYMBOLSOVER TEMPERATUREUND

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual2IMP/P SERIESPORTABLE SINGLE ZONE HORIZONTAL CONTROLLERPOWER SWITCHONOFFSTANDBY (WARM) REGI

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual3SECTION 1 OPERATING INSTRUCTIONSIMP Series 15 and 30 Amp Temperature ControllersIMP/P Seri

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual4The IMP controller also sends alarm status conditions to the SAMauxiliary module for annun

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual5is 30 ºF (17 °C) or more above setpoint, the over temperature alarm display (upper segment

IMP I IMP/P I SAM Hot Runner Controllers Instruction Manual6Manual Open-Loop Operation1. Position the mode select switch to open-loop (“ ”).2. Tur